Choices for Hex setup

I have MG3. I have not really used it much since I also have been using Fishman triple play. My question is this, If I get MG3 Hex what is the best setup I can use. I am asking about MG3 Hex since I use the TriplePlay with multiple midi channels via Omnisphere. I have different strings playing different synths.

I should also state that I have a MacBook and I am conscious of the pitfalls with using a Boss GP10 since it is no longer supported with drivers for Mac. So I don’t think using a pickup with is no longer supported is a practical idea.

So my questions revolve around…

  1. Does MG3 Hex support per string midi outputs
  2. Which pickup should I use
  3. If I need to purchase something like the VG800 or ?? which one should I get
  4. Is there another option that is neat and tidy to use MG3 Hex with besides the GK5

thanks.

there is a limit on per string outputs, as there are only three chains.

you can run two instances in a daw to get around this.

this is what standalone looks like with EAD / GB / E routed separately:

does ‘neat and tidy’ include replacing an existing pickup with a hex option?

1 Like

That looks fine. A little tight on being able to trigger different sounds via string. Is three the software limit on instances. I have a MacPro Max. with 48g so as far as processing power I know the computer could do more.

more explanations

I am trying to figure out if I can replace my tripleplay wireless with a more elegant system. I am getting a new guitar and I know that I will be using synths with it. I would prefer to have something that is mounted permanently on the guitar. I think this means probably the GK5. I don’t understand how much hardware I will need to make this work. I am looking for best case dependable with minimal monkey jack. A cable, ok- a different interface- ok. If it takes much more than that it begins to be a case of diminishing returns.

I currently use a Tripleplay Wireless. So I have Midi via dongle and then just route each string to a channel in Ableton and either use the multis in Omnisphere or Stack individual vst on that sub channel. Six channels of midi direct to the Daw wireless. What I don’t like about the way I am doing it now is the pod on top of the guitar and using sticky tape to make sure everything aligns properly.
I never know when I open the case if I will have to adjust the pickup or pod that has moved during transit.
The functionality is there but it is not the clean setup of having a permanent mount pickup.
On the guitar side I am using a Fractal AM4 wireless to audio and synth from computer comes out via UsB to Fractal Balanced outputs post Guitar Modeling.

There is a lot of talk on the forum but I can’t seem to locate the best possible way to setup 6 channels of synth using MG3. Before I spend the money on the upgrade to MG3hex and commit to more hardware I would like to know how people are succeeding in setting up the hex hardware in a clean and dependable way.

The fishman system just outputs 6 channels of midi direct to my Daw. I can easily route anything to anything. I do see that MG3 may have more possiblities but to get the individual string thing working I don’t really understand which hex pickup is really working with what hardware and what I need to do to get the 6 channels of signal into the daw as midi/audio.

I am really attracted to the MG3 but would like anecdotal accounts of how to make it all work.

To process the audio signals from individual strings, you first need a hexaphonic pickup that provides these signals separately.
Theoretically, you could then use six instances of MG3 across six audio tracks, allowing you to process and route the audio and MIDI data for each string independently.
Therefore, the first question you should ask yourself is: “Should I choose a hexaphonic pickup with an analog output?”—in order to gain access to the information from each individual string—rather than: “Should I use MG3 or MG3 Hex?” (the latter requires such a pickup in any case)

Hiya

Thanks for the reply but I am all in on what needs to happen but how about telling me how you make it work. I completely understand hex. I am looking for working examples. The nuts and bolts.

What pickup do you use? What computer and how do you make it so that you can take it out of the house and play with others? Inquiring minds want to know.

Btw. As I said in my above posts I already have tried MG3 and I bought it. MG3 can’t do what I want. I want to know how people are getting MG3 Hex to work.

This is an inquiry to see if other folks have a formula that works.

So my questions revolve around…

  1. Does MG3 Hex support per string midi outputs - Answered - yes it can.
  2. Which pickup should I use -still want to know
  3. If I need to purchase something like the VG800 or ?? which one should I get- suggestions?
  4. Is there another option that is neat and tidy to use MG3 Hex with besides the GK5- unknown

your pickup options:

  • boss gk: requires add’l boss hardware or a splitter cable and an audio interface
  • cycfi: a complete system including breakout box but expensive. requires an audio interface.
  • graphtech piezo: requires splitter cable and an audio interface.
  • ubertar: a more reasonably priced complete system, requires an audio interface.
  • subsix: has an issue with body noise, but a custom install may address this. requires an audio interface.

graphtech is perhaps closest to ‘neat and tidy’.

unfortunately there isn’t a large enough userbase to draw on to give you ‘best’ recommendations.

i have used all of the above. if i was a touring musician looking for reliable operation i’d go with the graphtech. if i wanted the best tone i’d go with the ubertar. if i was an acoustic player i’d go with the subsix.

1 Like

So the graph tech piezo just needs an audio interface?

I will look it up. Thank you.

I can confirm that the piezo saddles of the Graph Tech Ghost system work well but its one of the systems that require the most rework on your guitar. Recently I have listed up the hex-pickup (only audio / not MIDI) choices, have a look to attached file.

Hex-Pickup-Audio-Comparison.pdf (17.4 KB)

1 Like

really nice layout of all the informations. Double plus good.

1 Like

While not inexpensive, I really like the setup I am currently using.

  1. Boss GK5 pickup. I have used Roland/Boss systems since the early 80’s. I find the stereo cable to be much easier to deal with than most of the 13 pin cables that are out there. And as I run a separate guitar cable, I don’t find the lack of guitar audio with the external pickup to be an issue.
  2. Boss GKC-DA convertor. This box converts the digital signal from the GK5 to a 13 pin output.
  3. https://www.separate-strings.co.uk/ breakout cable. You need this to convert the 13 pin output to 6 analog outputs/
  4. Audio interface with 6 analog inputs. I use my Avid MTRX II with AD card for my input, but have used everything from Zoom F6 and F8n Pro to the new MOTU OctaLite.

Once you get your levels dialed in, this system is the most responsive and dynamic MIDI guitar I have ever used. Getting the levels set correctly is probably the biggest thing to get right for each player as it really corresponds to your playing style and what artifacts you will get. One thing I have found for me is that playing with my fingers vs a pick has really cleaned up the results and I also get way more dynamic response that I can with a pick.

From Roland, Axom, Yamaha, Casio, Fishman, and even the Rob O’Riley guitar, this has everything I need to reliably create MIDI parts that are in my head. I hope as we get towards the end of the year and things ease up, I plan on doing a series of videos to show how I set up and use MIDI Guitar 3.

And as far as using Omnisphere with a different sound per string, that would just be using Hex with a standard setup (either in MIDI 1.0 multi-channel or MPE with each string set to a different midi channel) and Omnisphere in multi mode. I don’t see a reason to go through the complexity of multiple chains and string splitters. I will try to check exactly how this would work and get back to you.

Gil

1 Like

Just tested Omnishpere in multi mode with MIDI 1.0 multi setup and it works fine. No need to create multiple chains and string splits.

1 Like

No one disputes this, however, he first needs a hex pickup and the corresponding peripheral equipment so that the six audio signals can reach his computer.

1 Like

There was an example of multiple chains and splitters earlier in the thread. I just wanted to make sure he knew it was possible without the complex routing. And yes that is why I started my response with my hex setup.

1 Like

The VG-800 is worth checking only if it exposes six separate string channels over USB audio to macOS; if it presents only a stereo or mono mix, it won’t give MG3 Hex the six inputs it needs. Otherwise the GK5 + GKC-DA + breakout into a 6-input interface is a known path, and Ghost piezo is neat but install-heavy. Once six streams arrive, map each string to its own MIDI channel and use Omnisphere multi mode.

1 Like

in terms of stage use, the boss products have a shortcoming - they don’t have balanced outs.

the typical 8 channel audio interface has those, plus dedicated physical knobs for each input’s gain and some offer independent headphone mixes which can be very helpful.

1 Like